Clover B7A Hot and Cold Bottled Water Cooler User Manual

1. Taw qhia

This manual provides essential instructions for the safe and efficient operation, installation, and maintenance of your Clover B7A Hot and Cold Bottled Water Cooler. Please read this manual thoroughly before using the appliance and retain it for future reference.

The Clover B7A water cooler is designed to dispense both chilled and hot water from a standard bottled water supply. It features a hygienic stainless steel water tank and a durable UV-protected, high-density polyethylene cabinet.

2. Cov ntaub ntawv kev nyab xeeb

WARNING: To reduce the risk of injury or property damage, read all instructions before assembling, installing, and operating this water cooler.

• Always place the water cooler on a level, stable surface.
• Xyuas kom muaj cua txaus nyob ib ncig ntawm lub tsev. Tsis txhob thaiv qhov qhib qhov cua.
• Tsis txhob khiav lub tsev nrog ib tug puas cord los yog plug.
• Keep children away from the hot water dispenser. The hot water temperature is approximately 185°F (85°C).
• Nco ntsoov tshem lub tshuab ua ntej ntxuav lossis ua haujlwm tu.
• Tsis txhob tso cov khoom siv, hlua, lossis ntsaws rau hauv dej lossis lwm yam kua dej.
• Cov cuab yeej no yog npaj rau kev siv sab hauv tsev nkaus xwb.

3. Teeb cov lus qhia

3.1 Unpacking

Carefully remove the water cooler from its packaging. Inspect the unit for any signs of damage. If damage is found, do not operate the unit and contact your retailer.

3.2 Qhov chaw

Place the water cooler on a hard, level surface capable of supporting its weight when a full water bottle is installed. Ensure there is at least 4 inches (10 cm) of clearance from the back and sides of the unit to allow for proper ventilation.

3.3 Kev Tu Thawj Coj

Before first use, clean the exterior of the unit with a soft, damp cloth. The removable drip tray should be washed with mild soap and water.

3.4 Installing the Water Bottle

Remove the protective seal from the top of a standard 3 or 5-gallon water bottle. Lift the bottle and carefully place it onto the bottle support on top of the cooler. The probe will push into the bottle, allowing water to flow into the internal reservoirs. A double float valve with a secondary safety float mechanism helps prevent spills.

Image: The Clover B7A water cooler with a clear water bottle correctly placed on its top-loading reservoir.

3.5 Flushing the System

Before plugging in the unit, dispense at least 1 liter of water from both the hot and cold spigots to ensure the reservoirs are filled and to flush any air from the lines. This prevents dry heating of the hot tank.

3.6 Kev sib txuas fais fab

Plug the power cord into a grounded electrical outlet. The unit will begin cooling and heating the water. Allow approximately 15-30 minutes for the water to reach optimal temperatures.

4. Cov lus qhia ua haujlwm

4.1 Kev Muab Dej Txias

Place your cup or container under the blue (cold) spigot. Push the blue lever down or lift it up to dispense cold water. Release the lever to stop the flow.

Image: The dispensing area of the Clover B7A, highlighting the hot (red) and cold (blue) water spigots and the removable drip tray.

4.2 Dispensing dej kub

CAUTION: Hot water is approximately 185°F (85°C) and can cause burns.

The hot water spigot (red lever) features a child-safety mechanism. To dispense hot water, first push the safety button inward, then push the red lever down or lift it up. Release both to stop the flow.

4.3 Adjusting Cold Water Temperature

The cold water temperature can be adjusted using the thermostat located on the back of the unit. Use a flathead screwdriver to turn the adjustment screw. Turning clockwise will make the water colder (down to 35.6°F / 2°C), while turning counter-clockwise will make it warmer (up to 53.6°F / 12°C).

5. Kev tu

5.1 Drip Tray Cleaning

The one-piece ABS drip tray is removable for easy cleaning. Periodically remove the tray, empty any collected water, and wash it with mild soap and water. Rinse thoroughly and replace.

5.2 Kev ntxuav sab nrauv

Clean the exterior cabinet with a soft, damp cloth. Do not use abrasive cleaners or solvents, as they may damage the UV-protected polyethylene surface.

5.3 Internal Cleaning / Descaling

For optimal performance and hygiene, it is recommended to clean and descale the internal water tanks every 3-6 months. Unplug the unit and remove the water bottle. Drain all water from the hot and cold tanks using the drain plugs located at the back of the unit. Follow manufacturer guidelines for descaling solutions or use a mixture of water and food-grade citric acid. Rinse thoroughly multiple times before re-installing a new water bottle and plugging in the unit.

6. Kev daws teeb meem

• Tsis Siv Neeg Dej Dej: Ensure the water bottle is properly seated and not empty. Check if the unit is plugged in.
• Tsis Muaj Dej Kub: Verify the hot water switch (usually on the back) is turned ON. Allow sufficient time for heating.
• No Cold Water: Verify the cold water switch (usually on the back) is turned ON. Allow sufficient time for cooling. Check the cold water thermostat setting.
• Tawm: Check the water bottle for cracks or damage. Ensure the bottle is correctly installed. Inspect the drain plugs at the back for tightness.
• Suab nrov txawv txawv: Some operational noise from the compressor or heating element is normal. Excessive or unusual noise may indicate an issue; ensure the unit is on a level surface and has adequate ventilation.

Yog tias muaj teeb meem tshwm sim tom qab sim cov kev daws teeb meem no, thov hu rau cov neeg siv khoom txhawb nqa.

7. Cov lus qhia tshwj xeeb

8. Warranty thiab Support

For warranty information or technical support, please refer to the documentation included with your purchase or contact Clover customer service directly. Keep your purchase receipt as proof of purchase for warranty claims.