Skytech 9800332 TS/R-2 Wireless Wall Mounted LCD Fireplace Remote Control Thermostat

Taw qhia

The Skytech 9800332 TS/R-2 system is designed to provide a safe, reliable, and user-friendly remote control solution for gas heating appliances. This manual will guide you through the installation, operation, and maintenance of your new wireless thermostat system.

Cov ntaub ntawv tseem ceeb ntawm kev nyab xeeb

Please read and understand all instructions before installing or operating this product. Failure to follow these instructions may result in property damage, personal injury, or death. Keep this manual for future reference.

• Ensure all wiring is performed by a qualified professional if you are unsure.
• Always turn off the gas supply to the appliance before performing any installation or maintenance.
• Do not expose the remote control or receiver to water or extreme temperatures.
• Replace batteries regularly to ensure proper operation and prevent leakage.
• This system is intended for use with gas heating appliances only.

Ntim Cov Ntsiab Lus

Xyuas kom tseeb tias txhua yam khoom muaj nyob hauv koj pob:

• Transmitter (Remote Control)
• Txais Box
• Phab ntsa Clip
• Phab ntsa
• Cov lus qhia installation
• Batteries (for transmitter and receiver)
• Temperature Sensor (integrated into the transmitter)

Khoom Tshajview

The Skytech 9800332 TS/R-2 is a wireless, wall-mounted thermostat system designed for convenient control of your fireplace. It features a clear LCD display and simple three-button operation.

Daim duab 1: Skytech 9800332 TS/R-2 Wireless Thermostat. The unit features an LCD screen displaying '72°F' and 'ROOM SET TEMP', with 'SKYTECH' branding below. At the bottom are three buttons: an 'ON' arrow button, a 'SET' button, and an 'OFF' arrow button.

Cov yam ntxwv tseem ceeb:

• 3-Button On/Set/Off wall mounted thermostat with LCD display
• LCD displays room and thermostat set temperature in °F or °C
• Battery powered receiver box with learn function and On/Remote/Off slider switch
• Receiver can be installed in wall, on the hearth or under the fireplace behind the control access panel
• Lighted display for easy viewhauv
• Tsawg roj teeb qhia

Kev teeb tsa thiab kev teeb tsa

1. Kev teeb tsa roj teeb

Install the provided batteries into both the transmitter (remote control) and the receiver box. Ensure correct polarity.

2. Receiver Placement

The receiver box can be installed in various locations:

• Inside the wall (using the wall plate)
• On the hearth
• Under the fireplace, behind the control access panel

Ensure the receiver is placed in a location where it can receive signals from the transmitter and is not exposed to excessive heat.

3. Kev Txuas Xov Tooj Rau Lub Tshuab Txais

Connect the receiver to your gas heating appliance's control valve according to the appliance manufacturer's instructions. Typically, this involves connecting two low-voltage wires from the receiver to the appliance's millivolt or 24V control terminals. Consult a qualified technician if you are unsure about wiring.

4. Pairing (Learn Function)

To establish communication between the transmitter and receiver:

1. Locate the "LEARN" button on the receiver box.
2. Press and hold the "LEARN" button until you hear a beep or see an indicator light flash.
3. Within 20 seconds, press any button on the transmitter.
4. The receiver will beep or flash again to confirm successful pairing.

Test the connection by pressing the ON/OFF buttons on the transmitter.

Cov lus qhia ua haujlwm

1. Fais fab / Off

• To turn the fireplace ON, press the ON (Up Arrow) khawm ntawm lub transmitter.
• To turn the fireplace OFF, press the OFF (Down Arrow) khawm ntawm lub transmitter.

2. Kev teeb tsa qhov kub thiab txias

The LCD displays both the current room temperature and the set temperature.

1. Nias lub SET button once. The set temperature will flash.
2. Siv cov ON (Up Arrow) or OFF (Down Arrow) nyees khawm los kho qhov xav tau kub.
3. Xovxwm SET again to confirm, or wait a few seconds for the setting to automatically save.

3. Switching Between °F and °C

Txhawm rau hloov qhov ntsuas kub ntsuas ntsuas:

• With the display showing the room temperature, press and hold the SET button for approximately 5 seconds until the unit changes.

4. Receiver Slider Switch

The receiver box has a slider switch with three positions:

• ON: Manually turns the fireplace ON, bypassing the remote control.
• NCO TSEG: Allows the fireplace to be controlled by the wireless transmitter. This is the standard operating position.
• Tawm: Manually turns the fireplace OFF, bypassing the remote control.

Kev tu

Hloov roj teeb

When the low battery indicator appears on the LCD, or if the system becomes unresponsive, replace the batteries in both the transmitter and receiver. Use fresh alkaline batteries of the specified type (refer to specifications). Dispose of old batteries responsibly.

Ntxuav

Wipe the surfaces of the transmitter and receiver with a soft, dry cloth. Do not use abrasive cleaners or immerse the units in water.

Kev daws teeb meem

Specifications

Warranty thiab Support

For warranty information and technical support, please refer to the documentation included with your purchase or contact SkyTech customer service directly. Keep your proof of purchase for warranty claims.

Chaw tsim tshuaj paus: Skytech