AVANTEK Wireless Doorbell CW-12 User Manual

1. Taw qhia

This manual provides detailed instructions for the installation, operation, and maintenance of your AVANTEK Wireless Doorbell CW-12. Please read this manual thoroughly before using the product to ensure proper function and longevity. This wireless doorbell system offers convenience and reliability for your home or office.

2. Cov ntsiab lus ntawm pob

Upon unpacking, please verify that all items listed below are included in your package:

• 1 × Transmitter (Doorbell Push Button)
• 2 × Plug-in Receivers (Chime Units)
• 1 × Adhesive Tape for Transmitter Mounting
• 2 × Screws for Transmitter Mounting
• 2 × Anchors for Transmitter Mounting
• 1 × Screwdriver
• 1 × Tus neeg siv phau ntawv

3. Khoom Nta

• 1000 ft (300 m) Ultra-Long Wireless Range: Ensures you never miss a visitor, even if you are a few rooms away or on another floor.
• 52 Chimes and Melodies: Choose from a wide selection of sounds with a 1.1 inch (29 mm) stereo speaker for rich, crisp audio.
• 5 Adjustable Volume Levels: Customize the sound level up to a maximum of 115 dB.
• LED Flash Qhov taw qhia: Provides a visual alert, useful for noisy environments or for individuals with hearing impairments.
• IP55 Dustproof and Waterproof Transmitter: Designed to withstand various harsh weather conditions, operating effectively from -4 °F to 140 °F (-20 °C to 60 °C).
• Memory Function: Remembers your last melody and volume level after a power outage, eliminating the need to reset settings.
• Compact Receiver Design: The mini plug-in receivers are designed not to block adjacent power sockets.
• Expandable System: Easily add more AVANTEK CR-1/RB-1 plug-in receivers for increased coverage.

4. Kev teeb tsa thiab kev teeb tsa

4.1. Kev teeb tsa txais

1. Plug the receiver into a standard electrical outlet. The LED on the receiver will flash, indicating it is powered on.

4.2. Transmitter Setup and Installation

The transmitter (push button) can be installed using either the adhesive tape or screws and anchors.

Method A: Using Adhesive Tape

1. Clean the desired installation area thoroughly to ensure it is free of dust and moisture.
2. Remove the protective film from one side of the adhesive tape and attach it to the back of the transmitter.
3. Remove the protective film from the other side of the adhesive tape.
4. Firmly press the transmitter onto the cleaned surface for at least 30 seconds.

Method B: Using Screws and Anchors

1. Open the transmitter cover by inserting the provided key into the grooved slot and gently prying it open.
2. Mark the positions for drilling holes on the wall using the back plate of the transmitter as a template.
3. Drill two holes at the marked positions. Insert the anchors into the holes.
4. Secure the back plate of the transmitter to the wall using the provided screws.
5. Snap the transmitter cover back onto the secured back plate.

5. Cov lus qhia ua haujlwm

5.1. Hloov Cov Nkauj

To select a melody, press the 'Next' or 'Previous' button on the side of the receiver. There are 52 melodies available. Once you find your desired melody, it will be saved automatically.

5.2. Kho qhov ntim

Press the 'Volume' button on the side of the receiver to cycle through 5 adjustable volume levels. Select the volume level that best suits your needs.

5.3. Hom ntsiag to

To activate silent mode, repeatedly press the 'Volume' button until the volume indicator shows the lowest setting or is muted. In silent mode, the LED indicator will still flash when the doorbell is pressed, providing a visual alert without sound.

5.4. Pairing Transmitter thiab Receiver

Your doorbell system comes pre-paired. If you need to re-pair or add additional transmitters/receivers:

1. Txuas lub receiver rau hauv lub qhov hluav taws xob.
2. Press and hold the 'Volume' button on the receiver for 3 seconds until the LED flashes rapidly. This indicates pairing mode.
3. Immediately press the push button on the transmitter. The receiver will chime once, and its LED will flash simultaneously with the transmitter's LED, indicating successful pairing.
4. Repeat the process for any additional transmitters or receivers.

6. Kev tu

6.1. Kev Hloov Roj Teeb (Lub Tshuab Xa Xov Tooj)

The transmitter uses a CR2032 lithium battery, which typically lasts up to 3 years. To replace the battery:

1. Insert the provided key or a small flat-head screwdriver into the grooved slot on the side of the transmitter.
2. Gently pry open the rear cover of the transmitter.
3. Ua tib zoo tshem lub roj teeb CR2032 qub.
4. Insert a new CR2032 battery, ensuring the positive (+) side is facing up.
5. Snap the rear cover back into place until it clicks securely.

7. Kev daws teeb meem

• No Sound from Receiver: Ensure the receiver is properly plugged into a working power outlet. Check the volume level and ensure it is not set to silent mode. Re-pair the transmitter and receiver if necessary.
• Transmitter Not Working: Verify the battery in the transmitter is correctly installed and has sufficient charge. Replace the CR2032 battery if needed. Ensure the transmitter is within the 1000 ft wireless range of the receiver.
• Kev cuam tshuam: Avoid installing the transmitter close to or on metal surfaces (e.g., metal door frames, metal mailboxes) as this can interfere with the wireless signal. Large metal objects or thick walls can reduce the effective range.
• Short Range: Obstacles such as thick walls, metal structures, or other wireless devices can reduce the operating range. Try relocating the receiver or transmitter to a different position.

8. Cov lus qhia tshwj xeeb

9. Warranty thiab Support

AVANTEK is committed to providing high-quality products and customer satisfaction. Our wireless doorbell is approved by FCC, CE, and RoHS standards. We offer dedicated customer service and will always do our best to support you with any inquiries or issues.

For further assistance or warranty claims, please refer to the contact information provided on the AVANTEK official website lossis koj cov ntaub ntawv yuav khoom.