CLOVER D25-B-TL Touchless Water Cooler Purifier Dispenser User Manual

Taw qhia

Thank you for choosing the CLOVER D25-B-TL Touchless Water Cooler Purifier Dispenser. This advanced system provides convenient access to purified cold and ambient water. Featuring a GAC filtration system, UV LED self-cleaning, and touchless dispense technology, it ensures a hygienic and refreshing hydration experience. This manual provides essential information for proper setup, operation, maintenance, and troubleshooting to ensure optimal performance and longevity of your dispenser.

Daim duab 1: Pem hauv ntej view of the CLOVER D25-B-TL Water Cooler Dispenser.

Cov ntaub ntawv tseem ceeb ntawm kev nyab xeeb

Thov nyeem tag nrho cov lus qhia ua tib zoo ua ntej siv lub tshuab. Khaws phau ntawv no rau yav tom ntej siv.

• Kev Nyab Xeeb Hluav Taws Xob: Ensure the dispenser is connected to a grounded electrical outlet. Do not use extension cords. Disconnect power before cleaning or servicing.
• Kev sib txuas dej: Connect the dispenser only to a potable water supply. Ensure all connections are secure to prevent leaks.
• Qhov chaw: Place the dispenser on a flat, stable surface. Allow adequate clearance around the unit for ventilation.
• Me Nyuam thiab Tsiaj Tsiaj: Keep children and pets away from the dispenser, especially during operation and maintenance.
• Kub: This unit dispenses cold and ambient water only. It does NOT produce hot water.
• Kev puas tsuaj: Do not operate the dispenser if it has a damaged cord or plug, or if it has been dropped or damaged in any way. Contact customer support.

Ntim Cov Ntsiab Lus

Verify that all items listed below are included in your package.

• CLOVER D25-B-TL Water Cooler Dispenser
• First Filter (GAC Purification System)
• Tubing dej
• Cov khoom sib txuas
• Emergency Shutoff Valve
• Tubing Clips
• Cov neeg siv phau ntawv

Daim Duab 2: Cov khoom siv teeb tsa suav nrog.

Teeb cov lus qhia

1. Unpacking: Carefully remove the dispenser and all components from the packaging. Retain packaging for future transport if needed.
2. Qhov chaw: Position the freestanding dispenser on a level, stable surface. Ensure there is adequate space around the unit for proper ventilation, especially at the rear where the cooling coils are located. The dimensions are approximately 13.58"D x 12.2"W x 43.3"H.
3. Filter Installation:
   • Locate the filter housing, typically at the rear or bottom access panel of the unit.
   • Insert the provided GAC purification filter into the housing as per the arrows indicating water flow.
   • Secure the filter firmly.
   

   Daim duab 3: Sab hauv view illustrating filter placement and water tubing.
4. Kev sib txuas ntawm Kev Siv Dej:
   • Connect the water tubing from your potable water source to the dispenser's inlet using the provided connectors and emergency shutoff valve.
   • Ensure all connections are tight to prevent leaks. Use tubing clips to secure the tubing if necessary.
   • Slowly open the water supply valve to allow water to fill the dispenser's internal tank. Check for any leaks.
5. Kev sib txuas fais fab: Plug the dispenser into a grounded 120V AC electrical outlet.
6. Initial Flush: Before first use, dispense several cups of water from both cold and ambient spouts to flush the system and filter. Discard this water.

Cov lus qhia ua haujlwm

The CLOVER D25-B-TL features touchless dispense and UV LED self-cleaning for enhanced hygiene.

1. Hwj chim On: Once plugged in, the dispenser will begin to cool the water. Allow approximately 1-2 hours for the water to reach optimal cold temperature (35.6°F).
2. Dispensing Water (Touchless):
   • Place your cup or container under the desired spout (cold or ambient).
   • Wave your hand in front of the sensor located above the spout. The water will begin to dispense.
   • Remove your hand to stop the water flow.
   

   Figure 4: Detail of the touchless dispense spouts and sensors.

3. UV LED Self-Cleaning: The dispenser is equipped with a UV LED self-cleaning system for enhanced water purification. This system operates automatically to maintain the hygiene of the internal water tanks. Refer to the indicator lights on the top panel for its status.

Kev tu

Regular maintenance ensures the best performance and water quality from your dispenser.

1. Filter Hloov:
   • The GAC purification filter should be replaced periodically, typically every 6 months or as indicated by the dispenser's filter change indicator (if present).
   • Turn off the water supply and unplug the dispenser before replacing the filter.
   • Follow the filter installation steps in the Setup section to replace the old filter with a new one.
   • Flush the new filter as described in the Initial Flush step.
2. Drip Tray Cleaning: The ABS drip tray is easily removed for cleaning.
   • Rub lub tais dej ntws mus tom ntej kom tshem nws tawm.
   • Empty any collected water and wash the tray with mild soap and water.
   • Rinse thoroughly and reinsert the tray.
3. Kev ntxuav sab nrauv: So cov chaw sab nrauv nrog cov mos mos, damp daim ntaub. Tsis txhob siv cov tshuaj abrasive los yog cov kuab tshuaj.
4. Internal Tank Cleaning: The UV LED self-cleaning system helps maintain internal hygiene. For additional cleaning, consult the manufacturer's website or customer support for specific instructions.

Kev daws teeb meem

Ua ntej hu rau cov neeg siv khoom txhawb nqa, thov saib cov teeb meem thiab cov kev daws teeb meem hauv qab no:

Specifications

Figure 5: Product dimensions for placement reference.

Warranty thiab Customer Support

For warranty information, product registration, or technical assistance, please contact CLOVER customer support.

Chaw tsim tshuaj paus: Clover
Webqhov chaw: CLOVER Official Store (rau cov ntaub ntawv dav dav txog cov khoom)
Thov saib koj cov ntaub ntawv yuav khoom kom paub txog cov nqe lus lav thiab cov ntaub ntawv tiv tauj.