DuraTherm Digital Heating Element Controller Phau Ntawv Qhia
ELECTRICAL Element WALL CONTROLER
Thov nyeem cov lus qhia kom meej ua ntej sim tit cov khoom lossis txuas rau koj lub tshuab hluav taws xob.
Thov xyuas kom meej tias koj xaiv ib qho khoom siv hluav taws xob tsim nyog rau koj lub phuam sov.
Kev Tiv Thaiv Kev Nyab Xeeb: Cov khoom no yuav tsum tau txhais los ntawm ib tus neeg muaj peev xwm uas tuaj yeem ua raws li IEE. Tshooj P thiab cov cai hauv zos. Xyuas kom lub mains hluav taws xob Circuit Court thiab lub fused spur unit yog ob leeg cais ua ntej fining. Chav tsev no yuav tsum tsis txhob muab tso rau hauv IEE chav dej Zone.1.
QHOV CHAW UA HAUJ LWM
Yuav tsum muaj fused spur nyob rau hauv cov khoom siv hluav taws xob rau tus maub los. haum nrog qhov loj me fuse.
2 x E & 2 x N terminals yog txuas rau ntawm lub rooj tsav xwm luam tawm.
ELECTRICAL Element WIRES (Tawm) |
Los ntawm sab laug mus rau sab xis terminals 1-3 sib haum mus rau Element cable Cov kab hluav taws xob yuav tsum tau txuas nrog raws li hauv qab no: Ntsuab / Yellow Earth to terminal 1 (N on board) Blue Neutral to terminal 2 (L on board) Brown Nyob to terminal 3 (L/T on board) TSEEM CEEB heev – Qhov no unit yuav tsum earthed |
MAIN CABLE WIRES (hauv) |
From Left to Right terminals 4-6 correspond to the Mains cable wires Lub mains cable xov hlau yuav tsum txuas raws li hauv qab no: Brown Nyob to terminal 4 (L on board) Blue Neutral to terminal 5 (N on board) Ntsuab / Yellow Earth to terminal 6 (E on board) VERY IMPORIANT – Qhov no unit yuav tsum earthed |
 |
Clamp lub caij cable mus rau hauv qab ntawm phab ntsa controller |
| Ua tib zoo haum lub phaj tswj rau hauv lub thawv tom qab kom ntseeg tau tias tsis muaj cov xov hlau raug kaw thaum lub sijhawm zaum. Siv ob txoj hlua kho kom ruaj ntseg rau lub thawv tom qab. |  |
Cov lus qhia ua haujlwm
There are four buttons on the control plate. ON/OFF (1), temperature Increase (2), kub txo (3), ECO boost button (4).
COV LUS QHIA KEV QHIA
The unit in standby has the main LED in RED. To turn on in normal mode, press the ON/OFF khawm thiab
release it. The LED yuav tig BLUE, tus ORANGE LED bank will light between one to five LED's.
To increase or decrease the temperature press the ‘increase/decrease’ buttons to attain the desired setting. Each one of the ORANGE LEDs represents the following power output from the element:
5 LEDs =100% power > 4 LEDs = 85% power > 3 LEDs = 70% power > 2 LEDs = 55% power >1 LED = 40% power
Tig lub unit OFF. nias lub ON/OFF khawm thiab tso nws.
NB The control plate contains a memory and whatever the temperature that was set when the unit was turned OFF, will be the temperature (number of LED’s lit) that the element will resume at when the unit is turned ON lwm zaus.
ECO FUNCTION
Press the ECU button from either power on or from standard control. the power LED will turn GREEN. The
ECO function allows you to go to a higher power setting for 30 minutes (To heat the towel warmer) this power level can be set in the first 30 minutes. After 30 minutes the power is reduced to the pre-set lower level for 90 minutes. The power output can be set using the increase/ decrease buttons to set your preferred rail temperature. After 2 Hours the controller will turn on.
Both the 30 minute and the 90 minutes settings are saved in the controller.
5 LEDs = 100% power > 4 LEDs = 85% power > 3 LEDs = 70% power > 2 LEDs = 55% power >1 LED = 40% zog
Technical Data.
Ingress tiv thaiv: IPX4
Voltage: 230-245 hli
Maximum tso zis ntau zog: 800 wb
Qhov Loj: 85 x 85 x 20 mm
Kev pom zoo: CE, tested to EN55014-1:2006
Cov ntaub ntawv / Cov ntaub ntawv
 |
DuraTherm Digital Heating Element Controller [ua pdf] Phau ntawv qhia Cov Hluav Taws Xob Hluav Taws Xob Hluav Taws Xob Hluav Taws Xob Hluav Taws Xob Hluav Taws Xob Hluav Taws Xob Hluav Taws Xob Hluav Taws Xob Hluav Taws Xob Hluav Taws Xob Hluav Taws Xob Hluav Taws Xob Hluav Taws Xob Hluav Taws Xob Hluav Taws Xob Hluav Taws Xob |