PATCHING PANDA Ephemere User Manual

PATCHING PANDA Ephemere User Manual

Taw qhia

Qhov no yog qhov kev daws teeb meem siab dual-channel kaw lus interface rau koj cov teeb liab feem ntau tsom rau kev kaw lus tswj voltages.

Koj tuaj yeem sau los ntawm 1014 sec ntawm 172Hz mus txog 4 sec ntawm 44.1kHz ntawm cov teeb liab ntawm txhua qhov channel, hloov qhov nrawm nrawm thiab luam theej duab los ntawm CV kaw.

Muaj lub lauj kaub attenuverter tshwj xeeb rau koj cov khoom xa tuaj. Thaum tsis muaj dab tsi yog patched rau cov tswv yim koj tuaj yeem siv lub lauj kaub input ua qhov offset / cv generator thiab sau cov lauj kaub txav mus rau hauv lub module.

Nws muaj peev xwm txuag, thauj koj cov teeb liab thiab teeb tsa ntawm SD daim npav txog 16GB ntawm qhov chaw
Muaj 4 hom kev kaw lus sib txawv los xaiv los ua cov teeb meem nyuaj ntxiv los npaj koj qhov kev ua yeeb yam nyob.

INSTALLATION

• Disconnect koj synth los ntawm lub hwj chim qhov chaw
• Muab ob npaug rau kos polarity los ntawm ribbon cable
• Tom qab txuas lub module xyuas dua koj tau txuas txoj kev yog, cov kab liab yuav tsum nyob rau ntawm -12V
• TSIS TXAUS SIAB RAU COV PINs los ntawm Pem Hauv Ntej PCB

TSIS TXAUS SIAB NTAWM IB TUG ME NYUAM YUAV TSUM TAU TXAIS yog tias koj tsis ua raws cov kauj ruam uas tau piav qhia saum toj no DAIM NTAWV THOV, Kev lav phib xaub yuav tsis raug them.

Cov lus qhia

• A) Teeb liab input 1
• B) Teeb liab input 2
• C) Cov ntaub ntawv input trigger 1
• D) Cov ntaub ntawv input trigger 2
• E) Play/Reset input trigger1
• F) Play/Reset input trigger2
• G) Channel 1
• H) Channel 2
• I) Scan CV input 1
• J) Scan CV input 2
• K) Ceev CV input 1
• L) Ceev CV input 2
• M) Attenuverter / Attenuate pot1
  (yog tias tsis muaj dab tsi patched xa VDC)
• N) Attenuverter / Attenuate pot2
  (yog tias tsis muaj dab tsi patched xa VDC)
• O) Speed ​​control pot 1
• P) Speed ​​control pot 2
• Q) Scan tswj lub lauj kaub 1
• R) Scan tswj lub lauj kaub 2
• S) Cov ntaub ntawv khawm 1
• T) Cov ntaub ntawv khawm 2
• U) Play/Reset khawm 1
• V) Play/Reset khawm 2
• W) Nres khawm 1
• X) Nres khawm 2
• Y) Rotatory Encoder
• Z) Xaiv khawm
  Tuav nias xaiv khawm rau 2 sec yuav hloov cov channel

Hloov kho FIRMWARE V 21.51

Cov ntawv qhia zaub mov dhia dej tau hloov pauv rau qhov kev paub zoo dua. Tswv yim txoj kev xaiv los ntawm kev sib txawv ntawm kev kaw, ua si cov cim.

Muaj 2 txoj cai ua raws li txhua yam yuav yooj yim dua thaum koj pib dhia mus rau hauv qhov chaw teeb tsa module.

Txoj Cai 1 "Xaiv khawm mus rau hauv cov ntawv qhia zaub mov ces xaiv qhov chaw"
Txoj Cai 2 "Nias encoder tawm ntawm cov ntawv qhia zaub mov, thiab hauv app nws hloov pauv OLED zaub los ntawm kev qhia cov teeb liab kaw los qhia cov teeb liab ADC"

Txhawm rau nkag mus rau cov ntawv qhia zaub mov tseem ceeb tuav nias lub pob xaiv rau 1 sec, tig lub encoder mus rau hauv cov ntawv qhia zaub mov, nias xaiv nkag.
Txhawm rau tawm hauv cov ntawv qhia zaub mov tsuas yog nias tus encoder.

Muaj cov ntawv qhia zaub mov tshiab hu ua "show in menu" los ntawm kev xaiv cov ntawv qhia zaub mov los ntawm cov npe, koj yuav ua kom 1 cov ntawv qhia tshwj xeeb rau kev nkag tau sai hauv app los ntawm nias lub pob xaiv, txoj kev no koj tuaj yeem muaj qhov tseem ceeb tshaj plaws xaiv rau lub teeb liab koj. tab tom ua haujlwm rau lub sijhawm ntawd.

Txhua lub teeb liab tau txais kev cawmdim hauv SD daim npav tseem yuav khaws cov chaw xaiv rau qhov tshwj xeeb ntawd

UA SI HOM

a) Loop: Lub playback ntawm lub teeb liab yuav ua si nyob rau hauv voj kom txog thaum STOP yog nias.
b) Ib qho kev txhaj tshuaj: Lub playback ntawm lub teeb liab yuav nres thaum nws mus txog qhov kawg lossis yog tias STOP raug nias.

Tuav nias PLAY khawm rau 2 sec, ua rau Kev Ua Si yog tsis quav ntsej LED yuav ntsais, qhov no yog qhov tseem ceeb rau REC Sync mult-G, rov ua kom lov tes taw.

PLAY DIRECTION

a) Tom ntej
b) Rov qab
c) Pendulum

QAUV QAUV

a) Quantized: Playback stepped ceev los ntawm /5, /4, /3, /2, x1, x2, x3, x4, x5.
b) Lineal: Playback ceev ntawm /5 txog x5

REC MODE

a) Phau ntawv: Nias REC yuav pib kaw, nias REC dua yuav ua kom tiav.
b) Phau ntawv mult: Nias REC yuav pib kaw, nias REC dua yuav ua kom tiav. (Yog tias PLAY raug nias thaum kaw, lossis qhov tshwm sim tau txais rau PLAY cov txheej txheem sau cia yuav raug nres, nias PLAY dua lossis tau txais lub cim rau PLAY input jack yuav txuas ntxiv kaw)
c) Sync: Nias REC yuav tos ib qho kev tshwm sim los ntawm REC txhais cov tswv yim pib sau, thaum lub thib ob txhais tau txais rau REC cov tswv yim dua yuav ua tiav cov ntaub ntawv.
d) Sync mult: Nias REC yuav tos kom muaj qhov cuam tshuam los ntawm REC cov lus qhia nkag los pib kaw, thaum lub cim thib ob tau txais rau REC cov tswv yim dua yuav ua tiav cov ntaub ntawv kaw tseg (Yog tias PLAY tau nias thaum kaw, lossis ua kom tau txais mus rau PLAY input kaw txheej txheem yuav yog. nres, nias PLAY dua lossis tau txais lub cim rau PLAY input jack yuav txuas ntxiv kaw)
e) Phau ntawv mult-G: Nias REC yuav pib kaw, nias PLAY yuav nres kaw qhov kawg ntawm kab sib chaws, nias REC tiav cov ntaub ntawv
f) Sync mult-G: Nias REC yuav tos kom muaj qhov cuam tshuam los ntawm REC cov lus qhia pib pib sau, thaum lub thib ob txhais tau txais rau REC cov tswv yim dua yuav ua tiav cov ntaub ntawv kaw tseg (thaum kaw yog qhov ua rau PLAY tau txais yuav teeb tsa cov phiaj xwm hauv cov ntaubntawv povthawj siv. txheej txheem)

Thaum VCA tau qhib, lub lauj kaub tawm tswv yim lossis lub teeb liab tawm tswv yim dhau los ua kev tswj hwm rau PLAYBACK SIGNAL. Nws yog ib qho tseem ceeb kom nkag siab txog CV RANGE ua ke nrog VCA qhov tshwj xeeb, yog tias koj ua haujlwm nrog 0V-10V cov cim qhia kom paub tseeb tias qhov kev hloov pauv tom qab PCB phim CV RANGE dhau lawm, tib yam siv rau -5V / + 5V cov cim.

QUANTIZER
Enabling Live CV input / Sau CV quantized 1V / oct

SCALES
Cov ntawv qhia zaub mov rau qhib / kaw cov ntawv

SAMPLING RATE
Xaiv qhov sib txawv sample tus nqi hom thiab lub sij hawm ntev ntawm cov ntaubntawv povthawj siv

CV Range
Hloov qhov offset ntawm lub teeb liab los ntawm -5 / + 5V lossis 0/10V, nws tuaj yeem hloov pauv qhov offset ntawm lub teeb liab playback.

FILE

File Thauj khoom: Loads signals rua ntawm SD card
File lwv: Erases cov cim tseg rau hauv SD daim npav
File Txuag: Txuag thiab sau npe cov cim ntawm daim npav SD

Qhia hauv MENU
Los ntawm kev xaiv cov ntawv qhia zaub mov los ntawm daim ntawv teev npe, koj yuav ua kom 1 cov ntawv qhia tshwj xeeb rau kev nkag ceev hauv app los ntawm nias lub pob xaiv, txoj kev no koj tuaj yeem muaj qhov zoo tshaj plaws xaiv rau lub teeb liab uas koj ua haujlwm rau lub sijhawm ntawd.

CALIBRATION
Nkag mus rau calibrating ADC / DAC ntawv qhia zaub mov

SELECT GRID AXIS
Thaum REC MODE MANUAL MULT G xaiv nrog qhov kev xaiv no koj tuaj yeem kho qhov kawg ntawm daim phiaj ib yam nkaus.

CALIBRATION

Ua ntej koj pib calibration:
Txuas lub CV tawm ntawm koj cov sequencer mus rau Ephemere cov tswv yim, cov zis los ntawm Ephemere rau koj VCO, VCO tawm rau koj DAW, hauv koj
DAW qhib tuner VST los saib xyuas cov ntawv. Ephemere input pot's ntawm MAX.

a) Mus rau hauv cov ntawv qhia zaub mov calibration, pib calibration txheej txheem.
b) Ntawv qhia zaub mov 0.0V, xa C0 los ntawm koj lub sequencuer, DAW tsis tuaj yeem ncav cuag C0 koj tsuas tig lub encoder kom phim tus nqi DAC nrog ADC tus nqi. Nyem 1 zaug nkaus xwb thiaj li mus rau kauj ruam tom ntej.
c) Ntawv qhia zaub mov 1V, xa C1 los ntawm koj cov sequencer, tig lub encoder thaum saib xyuas koj DAW kom ncav cuag C1

Nias SELECT khawm ib zaug yuav sau tus nqi, yuav dhia mus rau tom ntej voltage teeb. Nco ntsoov tsis txhob nias kom txog thaum koj xa qhov xav tau voltage mus rau npe, tsis txhob nias 2 zaug txwv tsis pub koj yuav tau pib dua.

c) Ntawv qhia zaub mov 2V, xa C2 los ntawm koj cov sequencer, tig lub encoder thaum saib xyuas koj DAW kom ncav cuag C2

d) Rov ua tib yam txheej txheem tshwj tsis yog 10V, vim DAW tsis tuaj yeem ncav cuag C10 koj yuav xav tau kom phim ADC thiab DAC qhov tseem ceeb.
e) Txuag calibration, tawm los ntawm nias encoder, reboot lub module
f) Xyuas yog tias calibration yog ok, xyuas kom meej CV ntau yog teem rau 0-10V thiab quantizer enabled.