xylem FlexNet CommandLink II Wireless Interface User Guide

Cov Lus Qhia Ceev
AQG-10087-05
FlexNet CommandLink II

FlexNet CommandLink II Wireless Interface

The CommandLink® II wireless interface provides access to a complete suite of functional controls within a gas, water, or electric SmartPoint® transceiver. This Bluetooth® enabled device, coupled with a handheld, can perform activations, deactivation, meter read, on-demand reads, and audits of the SmartPoint module.

Ceeb toom: Risk of hot surface. Do not hold the device longer than one (1) minute when operating in an ambient temperature above 40°C (104°F).

Kauj ruam 1: Them lub CommandLink II
You must charge the CommandLink II completely before first use.

1. Plug the charging adapter into a power outlet and connect to the Charging Port located next to the Mag Loop on top of the Command Link II.
   Nco tseg: Make sure you have rechargeable batteries installed before using a power outlet.
   Cov chav tsev uas tsis muaj roj teeb rov qab yuav tsum tsis txhob muab ntsaws rau hauv lub qhov hluav taws xob rau kev them nyiaj.
2. Lub teeb liab LED teeb pom kev, qhia tias chav tsev them nyiaj.
3. Unplug the unit when the red LED is no longer illuminated, indicating the CommandLink II is fully charged.
   Nco tseg: To power down the CommandLink II immediately, press and hold the power button located on the side of the CommandLink II until the PWR LED turns off.

Kauj ruam 2: Qhib Command Link II

1. Nias lub hwj huam khawm.
2. Lub teeb ntsuab LED illuminates thaum CommandLink II tau ua tiav lub zog.

Kauj ruam 3: Tsim Bluetooth Partnership
To use the CommandLink II, you must first establish a Bluetooth partnership with a Windows Mobile, Android, or iOS-equipped handheld device (HHD) or PC.

Ntim Cov Ntsiab Lus

• FlexNet CommandLink II
• Bungee Straps (2)
• Charging Adapter (AC / DC)
• Tsheb Charging Adapter (DC / DC)
• Case

Yog tias siv Windows Mobile Hand-Hold Device:

1. Xaiv Start, ces Settings.
2. Select Connections, then select Bluetooth COM.
   Power on the CommandLink II if it is off.
3. Xaiv Discover Devices.
   A list of all the Bluetooth-enabled devices in range is generated and displayed.
   If your CommandLink II does not appear in the list, make sure that it is powered on. If it is powered on, power cycle it and select Discover Devices again, and repeat this step.
4. Xaiv koj
   CommandLink II from the list and select Connect.
5. If you are prompted toSet the Bluetooth PIN, enter 0000 and select OK.
6. Xaiv OK kom tawm.
7. Xaiv X hauv kaum sab xis kom tawm.
8. Xaiv cov cuab yeej FieldLogic los ntawm Start menu.
9. From the FieldLogic Tools main screen, select Menu, and select Options.
10. Xaiv lub FlexNet tab thiab xaiv CommandLink los ntawm cov ntaus ntawv hom dropdown. Tsis xaiv CLxxxxxxxxx_BLE.
11. Xaiv Tau Status. Cov cuab yeej FieldLogic txuas nrog CommandLink II thiab qhia cov lus ua tiav.
12. Xaiv OK.
13. Xaiv OK dua kom rov qab mus rau Connect screen.

Yog tias siv Android ntaus ntawv:

1. Xaiv qhov chaw icon.
2. Select Options, then select FlexNet. FieldLogic displays a list of available devices.
3. Xaiv + rau view qhov system pairing screen.AQG – 10007 – 05
4. Xaiv koj CommandLink II (CLxxxxxxxxx) los ntawm cov npe ntawm cov khoom siv Bluetooth muaj.
5. Xaiv Pair. Koj CommandLink II ces tso rau hauv Paired Devices list.
6. Rov qab mus rau FieldLogic Cov Cuab Yeej.
7. Select the newly-paired CommandLink II in the list and select the information symbol.FieldLogic txuas mus rau CommandLink II thiab qhia cov lus ua tiav.
8. Xaiv Kaw.
9. Xaiv lub nraub qaum rov qab mus rau FieldLogic lub vijtsam loj.

Yog tias siv lub iOS Hand-held Device:

1. Xaiv qhov chaw icon.
2. Xaiv Options, ces xaiv FlexNet. FieldLogic scans rau lub cuab yeej thiab tom qab ntawd tso tawm cov khoom siv. Cov npe refreshes cia li.
3. Ib qho kev tso cai pop-up qhov rais qhia. Xaiv OK.
4. Xaiv koj CommandLink II (CLxxxxxxxxx) los ntawm cov npe ntawm cov khoom siv Bluetooth muaj.
   
5. Select your CommandLink II and then select the information symbol.
6. FieldLogic txuas mus rau CommandLink II thiab qhia cov lus ua tiav.
7. Xaiv Kaw kom rov qab mus rau Kev Xaiv qhov screen.
8. Xaiv lub nraub qaum rov qab mus rau FieldLogic lub vijtsam loj.

Yog tias siv PC:

1. Fais fab mus rau CommandLink II.
2. Xaiv lub cim Bluetooth ntawm koj lub computer lub desktop lossis los ntawm Start menu.
3. Los ntawm Bluetooth Devices pane, xaiv Ntxiv ib lub cuab yeej.
4. Koj lub computer tshawb nrhiav cov khoom siv ntxiv.
5. Select the icon containing the CommandLink II ID number (CLxxxxxxxx).
   Nco tseg: If two numbers appear, make sure you select CLxxxxxxxx. Do not select CLxxxxxxxx_BLE.
6. Xaiv Tom ntej.
7. Your computer confirms the successful addition of the CommandLink II.
8. Xaiv Kaw mus txuas ntxiv.
9. Pib cov cuab yeej FieldLogic. Los ntawm lub vijtsam tseem ceeb, xaiv Cov Cuab Yeej thiab xaiv Cov Kev Xaiv.
10. Xaiv qhov FlexNet Settings expander thiab xaiv CommandLink los ntawm Kev Sib Txuas Lus Ntaus Cov Ntawv Teev Npe. Xaiv koj lub cuab yeej los ntawm lub npe ntaus ntawv nco-down daim ntawv teev npe.
11. Select Get Status.
    FieldLogic Tools connects with the CommandLink II and displays a success message.
12. Xaiv OK kom rov qab mus rau qhov Options screen.
13. Xaiv OK kom rov qab mus rau Connect screen.

Attach a Strap to the CommandLink II

To attach a strap, slide it in between the slots on the sides of the unit.

AQG – 10007 – 05

Cov Lus Qhia Ua Raws Cai

CEEB TOOM
Any modifications made to this device that are not approved by Sensus may void the authority granted to the user by the FCC to operate equipment.

CEEB TOOM
Rau Chav Kawm B - Tsis txhob tso siab rau Radiators:
This device complies with Part 15 of the FCC Rules. Operation is subjectto the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

CEEB TOOM
ICES-003 Class B Daim Ntawv Ceeb Toom—Avis NMB-003, Chav B
Chav kawm B cov cuab yeej digital no ua raws li Canadian ICES-003.

CEEB TOOM
Nco tseg: Cov cuab yeej no tau raug sim thiab pom tias ua raws li cov kev txwv rau Class B cov cuab yeej digital, ua raws li Tshooj 15 ntawm FCC Cov Cai.
Cov kev txwv no yog tsim los muab kev tiv thaiv tsim nyog tiv thaiv kev cuam tshuam tsis zoo hauv kev teeb tsa hauv tsev. Cov cuab yeej no tsim, siv, thiab tuaj yeem tawg lub zog ntawm xov tooj cua thiab, yog tias tsis tau nruab thiab siv raws li cov lus qhia, yuav ua rau muaj kev cuam tshuam rau kev sib txuas lus hauv xov tooj cua. Txawm li cas los xij, tsis muaj kev lees paub tias kev cuam tshuam yuav tsis tshwm sim hauv ib qho kev teeb tsa tshwj xeeb. Yog tias cov cuab yeej no ua rau muaj teeb meem cuam tshuam rau lub xov tooj cua lossis TV txais tos, uas tuaj yeem txiav txim siab los ntawm kev tig cov khoom siv thiab qhib, tus neeg siv tau raug txhawb kom sim kho qhov cuam tshuam los ntawm ib lossis ntau qhov kev ntsuas hauv qab no:

• Reorient los yog tshem tawm cov kav hlau txais xov
• Ua kom muaj kev sib cais ntawm cov khoom siv thiab lub receiver
• Txuas cov cuab yeej siv rau hauv qhov hluav taws xob ntawm lub voj voog sib txawv ntawm qhov uas lub receiver txuas nrog
• Nrog rau tus neeg muag khoom lossis tus kws tshaj lij xov tooj cua / TV rau kev pab

CEEB TOOM
Cov cuab yeej no ua raws li Kev Lag Luam Canada daim ntawv tso cai-tsim RSS tus qauv (s). Kev khiav hauj lwm yog ua raws li ob qho xwm txheej hauv qab no: (1) cov cuab yeej no yuav tsis ua rau muaj kev cuam tshuam, thiab (2) cov cuab yeej no yuav tsum lees txais kev cuam tshuam, suav nrog kev cuam tshuam uas yuav ua rau lub tshuab ua haujlwm tsis xav tau.

CEEB TOOM
This radio transmitter, the Sensus CL201, has been approved by Industry Canada to operate with the antenna types listed below, with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

CEEB TOOM
Raws li Kev Lag Luam Canada txoj cai, lub xov tooj cua xa xov tooj cua no tsuas yog ua haujlwm siv lub kav hlau txais xov ntawm hom thiab qhov siab tshaj plaws (lossis tsawg dua) tau txais kev pom zoo rau lub tshuab xa tawm los ntawm Kev Lag Luam Canada. Txhawm rau txo cov xov tooj cua cuam tshuam rau lwm tus neeg siv, hom kav hlau txais xov thiab nws qhov nce yuav tsum tau xaiv kom qhov sib npaug isotropically radiated hwj chim (eirp) tsis ntau tshaj qhov tsim nyog rau kev sib txuas lus zoo.

CEEB TOOM
There is a danger of explosion if batteries are mishandled or incorrectly replaced. On systems with replaceable batteries, replace only with the same manufacturer and type or equivalent type recommended per the instructions provided in the product service manual.
Tsis txhob disassemble cov roj teeb lossis sim rov qab them lawv sab nraum lub system. Tsis txhob muab cov roj teeb pov tseg rau hauv hluav taws.
Pov tseg cov roj teeb kom raug raws li cov chaw tsim khoom cov lus qhia thiab cov cai hauv zos.

CEEB TOOM
TSIS TXHOB ua kom kub hnyiab lossis cuam tshuam cov roj teeb rau qhov kub thiab txias tshaj 212 ° F. Cov kev kho mob zoo li no tuaj yeem ua rau cell rupture.

CEEB TOOM
EXPLOSION HAZARD – BATTERIES MUST ONLY BE CHANGED IN AN AREA KNOWN TO BE NON-HAZARDOUS.

xyem.com
SENSUS | 637 Davis Drive | Morrisville, NC 27560 | 800.638.3748 | sensus.com

©2026 Sensus. All products purchased and services performed are subject to Sensus’ terms of sale, available at either sensus.com/TC or 1-800-638-3748. Sensus reserves the right to modify these terms and conditions in its own discretion without notice to the customer. The Sensus logo is a registered trademark of Sensus.
This document is for informational purposes only, and SENSUS MAKES NO EXPRESS WARRANTIES IN THIS DOCUMENT. FURTHERMORE, THERE ARE NO IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, WARRANTIES AS TO FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY. ANY USE OF THE PRODUCTS THAT IS NOT SPECIFICALLY PERMITTED HEREIN IS PROHIBITED.