YARBO Remote Controller Designed User Manual

YARBO Remote Controller Designed

Specifications

Physical Controller Instructions for 2024 Lawn Mower

• This guide offers instructions on using the Yarbo physical controller to operate your Yarbo lawn mower with maximum efficiency. Featuring intuitive controls for speed, mower operations, and other key settings, the controller enables seamless handling for various tasks. Follow these guidelines to master the controller and unlock the full potential of your Yarbo lawn mower.

Kev sib txuas

Tswj tuav

1. Locate the Physical Controller Holder provided in the Yarbo Core package and locate the side button on the Holder.
2. Locate the shafts and holes and press the buttons on both sides of the Holder, and then press the middle part as shown in the picture.

Khawm Taw Qhia

Yarbo Logo Button:

• Logo button can be used to power on or off the controller. To power on the controller, short-press the Logo button for 1 second. To power off, press the Logo buttons for 3 seconds. If the controller is not in use, it will automatically power off after 5 minutes.

Yarbo connecting mode

• Phone Connecting Mode

RB&LB (Safety button):

• RB and LB are designed to be the safety buttons, which means that either of these two buttons should be pressed throughout most of the operation. Except for the X/A/B/Y buttons and D-pad buttons, the rest of the buttons should be pressed with the RB/LB button to execute its function.

Switch & Clear Button:

• Long-press the switch or clear button for seconds to take over the control authority. Once the physical controller gains authority, you can operate the lawn mower.
• Short press the switch or clear button to exit the error mode. When Yarbo encounters the dangers or stuck by any obstacles, it will stop and enters the error mode. After the dangers are cleared, pressed the start or clear button to exit the erorr mode.

RB & LB (Safety button):

• RB and LB are designed as safety buttons, which means that one of the buttons should be pressed throughout most of the operation that may cause dangerous result. Except for the X/A/B/Y buttons and D-pads, the rest of the function buttons must be pressed with one of the safety buttons to execute their own functions.

Left Joystick and Right Joystick:

• These two joysticks control the direction of movement and speed of the robot. Press the safety button (RB/LB) and rotate the stick around to control Yarbo’s movement in any direction. Press the left and right sticks vertically down to switch between two-speed settings (L3, R3 button).

LT + RT Button:

• Keep the safety button pressed (RB/LB) and long press the LT+RT buttons for 2 to 3 seconds to open the cutting discs.

Directional Pad (D-pad):

• Press the up and down button to control the cutting discs height.

Y khawm:

• This button controls the lawn mower module to pitch up. Press and hold the button to continuously pitch up the lawn mower module until it reaches the highest position. Release the button to stop at the current angle.

A khawm:

• This button controls the lawn mower module to pitch down. Press and hold the button to continuously pitch down the Lawn Mower Module until it reaches the lowest position. Release the button to stop at the current angle.

B khawm:

• Press this button to turn on and off the front lights (default setting is on)

X khawm:

• Press this button to turn on and off all the lights (default setting is on)

Battery Indicator Button and Controller Light Button:

• Roj Ntsuas Qhia Tau Roj Hmo: Check Yarbo’s battery status at any time.
• Controller Light Button: Turn on the controller’s lights for better visibility during night or low-light operations.

Nta

• Universal Compatibility: Works with a wide range of devices such as smart TVs, projectors, air conditioners, and more.
• Ergonomic Tsim: Comfortable, easy-to-hold design for prolonged use.
• Advanced Technology: Utilizes infrared (IR) or Bluetooth connectivity depending on the model.
• Programmable Khawm: Customizable buttons for frequently used functions.
• Lub neej roj teeb ntev: Energy-efficient design that lasts for extended periods on a single battery.

Yuav siv li cas

Kauj ruam 1: Fais fab rau

• Press the Power button on the remote to turn it on. The LED indicator will blink, signaling that the remote is ready to pair with a device.

Kauj ruam 2: Pairing lub chaw taws teeb

• For IR-Controlled Devices:
  • Simply point the remote at the device you wish to control (e.g., TV, air conditioner).
  • Use the device-specific buttons (e.g., power, volume, input) to test the connection.
• For Bluetooth-Controlled Devices:
  • Press and hold the Bluetooth Pairing button (if applicable) for about 3-5 seconds until the LED indicator starts blinking rapidly.
  • On your device (e.g., smart TV or Bluetooth-enabled device), activate the Bluetooth pairing mode.
  • Select the YARBO Remote Controller from the list of available devices.

Step 3: Using the Buttons

• Cov YARBO Remote Controller features a range of customizable buttons for controlling devices:
  • Hwj chim: Turns the device on/off.
  • Volume Up / Down: Kho cov theem suab.
  • Channel Up/down: Changes channels (for TVs or similar devices).
  • Tswv yim: Switches between different input sources (HDMI, TV, etc.).
  • Cov nyees khawm: Some models feature programmable buttons for quick access to your most-used functions. Refer to the next section for programming instructions.

Kauj ruam 4: Kho tej chaw

• Brightness & Contrast (for compatible devices): Adjust the settings directly from the remote control.
• Hom Hloov Mus (for air conditioners or other smart devices): Cycle between modes like Cool, Heat, Fan, etc.

Kev daws teeb meem